QSXP on QSBASE3

../../_images/QSXP-QSBASE3.png

This guide will help new users to quickly setup our QSXP on QSBASE3 Linux Development Kit.

Detailed information about the QSXP solder-in module itself is available on our website.

Unboxing

When opening the package of the Development Kit you should find the following components inside:

  1. The evaluation board “QSBASE3” with the QSXP module soldered on.
  1. An USB cable which is used for power-connection and flashing.
  2. A TTL to USB Serial Converter cable.
  1. Our catalog and the QSXP datasheet.
../../_images/Verp_21.jpg
../../_images/Verp_11.jpg
../../_images/Verp_31.jpg

Wiring

Connect the QSBASE3 board as shown in the image below.

  1. Connect the TTL to USB Serial Converter cable to the DEBUG UART port on the board, notice the black wire on Pin 1. The other side is connected to your computer.
  1. Connect the USB to the board. The other side is also connected with your host computer.
  1. Verify the Bootmode-jumper is not in Download-Mode. For help see Enabling USB-Bootmode.
../../_images/qsxp-uart-wiring.png
../../_images/qsxp-usb-wiring.png
../../_images/qsxp-bootmode.png

Booting

After connecting the micro USB your board will boot.

U-Boot 2020.04-5.4.24-2.1.0+g603345d2df (Oct 12 2020 - 10:42:27 +0000)                                                                                                                 

[...]

Hit any key to stop autoboot:  0
14753800 bytes read in 340 ms (41.4 MiB/s)
## Flattened Device Tree blob at 43000000
   Booting using the fdt blob at 0x43000000
   Loading Device Tree to 0000000062fef000, end 0000000062ffffff ... OK
serial-number: 2d70c9dd0002aaff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.4.47-2.2.0+g5ec03d06f54e (support@karo-electronics.de) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Thu Nov 5 11:48:38 UTC 2020
[    0.000000] Machine model: Ka-Ro electronics QSXP-ML81 (NXP i.MX8MP) module on QSBASE3 baseboard
[    0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030890000 (options '115200')
[    0.000000] printk: bootconsole [ec_imx6q0] enabled
[    1.359142] imx-drm display-subsystem: no available port
INIT: version 2.88 booting
Initializing /var... Done.
Starting udev
ALSA: Restoring mixer settings...
INIT: Entering runlevel: 2
/usr/sbin/alsactl: load_state:1735: No soundcards found...
Configuring network interfaces... eth0: waiting for carrier
eth0: carrier acquired
DUID 00:01:00:01:c7:92:bd:1f:00:0c:c6:88:ea:90
eth0: IAID c6:88:ea:90
eth0: adding address fe80::15a7:3b6e:6744:d573
ipv6_addaddr1: Operation not supported
eth0: soliciting an IPv6 router
ipv6nd_startrs1: Address family not supported by protocol
eth0: soliciting a DHCP lease
eth0: offered 192.168.0.21 from 192.168.1.1
eth0: probing address 192.168.0.21/23
eth0: leased 192.168.0.21 for 72000 seconds
eth0: adding route to 192.168.0.0/23
eth0: adding default route via 192.168.1.90
forked to background, child pid 1669
done.
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting ntpd: done
Starting syslogd/klogd: done

karo-minimal (Ka-Ro Linux BSP with minimal read-only rootfs) 5.4-zeus qsxp-ml81 /dev/ttymxc0

qsxp-ml81 login:

Your module is pre-programmed with our karo-image-minimal headless Linux.

Next Step Usage

Topic Description
Re-installing the OS
  • The pre-compiled Image files to flash the QSBASE3 Development Kit are located in our Download Area.
  • They contain a headless and a display environment.
  • Download the Images and proceed with the UUU - Universal Update Utility.
Display support

The QSBASE3 Development Kit supports the official Raspberry Pi 7inch Touch Display. The QSBASE3 can be mounted directly to the display.

Tip

The official Product Site of the Raspberry Pi 7inch Touch Display: https://www.raspberrypi.org/products/raspberry-pi-touch-display/

The sources supporting the Display are integrated our Yocto Layer. Refer to our Yocto Guide.

We also provide a Ready To Use qsxp-ml81-weston image to flash your QSXP module in our Download Area.

../../_images/draufsicht3.png
../../_images/display3.png

Next Step Software

Topic Description
Linux Guide

This guide refers to the use of images built with Yocto NXP Zeus.

Go to: Software Documentation -> QSXP -> NXP Zeus BSP

WiFi Guide

To enable WiFi support.

Go to: Software Documentation -> QSXP -> WiFi/BT Guide

Camera Guide

To enable camera support.

Go to: Software Documentation -> QSXP -> Camera Guide

Customizing the BSP

If you want to use our Yocto Layer, or want to create your own customized Linux distribution, have a look at our Yocto Guide.

Go to: Yocto Guide

Next Step Hardware

Topic Description
QSBASE3 Pinouts

Connector pinouts can be found in the Hardware Documentation.

Go to: Hardware Documentation -> Pinouts -> QSBASE3

QS Developers Guide

QS-Standard pinout, description and layout guidelines.

Go to: Hardware Documentation -> QS-GUIDE